The Bullnose Corner Trowel for drywall finishing is lightweight and sturdy. It’s handle and trowel head are made from durable plastic. The taping portion of the trowel is composed of rubber and creates a flexible edge for contact with any 3/4" bullnose corner. This trowel will spread joint compound evenly along both sides of bullnose corners, while also removing the excess compound from the exposed portion of the cornerbead. The Bullnose Corner Trowel is manufactured by Flannery, Inc.

The Bullnose Miter Tool is a special striking guide that allows you to mark and cut perfect miter cuts for bullnose corners. The Miter Striking tool is a template that is laid over a piece of Bullnose Cornerbead and then the installer strikes a line to show where the miter cut should be made. It is compatible with 3/4" Bullnose Corners, 135º Splay Bullnose Corners, and Bullnose Kerf Trims. It is a perfect tool for installing bullnose corners around door and window openings. The Bullnose Miter Tool is manufactured by Flannery, Inc.

This revolutionary fastening clip for steel studs is composed of 20 ga. Spring Steel. It is used for all kinds of Deflection Track Systems. Simply put the “Comp Clip” (Compression Clip) around the steel stud and then slide it onto the deflection track or floor track to hold the studs in place. It allows for 100% unobstructed movement. The Comp Clip is faster and easier than other stud clips on the market. It is available for both 1 3/8” (1.375”) and 1 5/8” (1.625”) width studs. Please be sure to choose the proper size when ordering. The Comp Clip is manufactured by Flannery, Inc.

Bullnose Base & Crown Plugs are ideal for filling the gap that is left when a 90º Base or Crowning Corner is used with Bullnose Cornerbead. The Plug is simply dropped into the gap that is formed between these two dissimilar materials. The Plugs are tapered to ensure a snug fit and uniform installation. They fit any size of base or crown moulding, no matter the thickness or height, and have a 3/4" radius to allow for a fit with any 3/4"” Bullnose Corner. Bullnose Base & Crown Plugs are manufactured by Flannery, Inc.

The Metal 3-Way Outside Bullnose Corner Cap is the only one of its kind. With its patented self-locking tabs, the Metal Corner Cap locks itself to the drywall while you install the Bullnose Corners over it. The Metal Corner Cap allows you to use about 50% less joint compound when finishing compared to its plastic counterparts. It not only saves you money on fasteners and joint compound, but it is one of the cheapest Drywall Bullnose Corner Caps on the market today. The Metal 3-Way Outside Bullnose Corner Cap is manufactured by Flannery, Inc.

The Vinyl 3-Way Outside Bullnose Corner Cap allows you to join three separate lines of Bullnose Corners that meet at an Outside 90º corner. This vinyl corner cap can be fastened to the drywall with nails, screws, or adhesive. The Vinyl 3-Way Outside Bullnose Corner Cap is manufactured by Trim-Tex, Inc.

The Vinyl 2-Way Bullnose Corner Cap allows you to join two separate lines of Bullnose Corners that meet at a 90º corner. This vinyl corner cap can be fastened to the drywall with nails, screws, or adhesive. The Vinyl 2-Way Bullnose Corner Cap is manufactured by Trim-Tex, Inc.

The Vinyl 3-Way Inside Bullnose Corner Cap allows you to join three separate lines of Bullnose Corners that meet at an Inside 90º corner. This vinyl corner cap can be fastened to the drywall with nails, screws, or adhesive. The Vinyl 3-Way Inside Bullnose Corner Cap is manufactured by Trim-Tex, Inc.

The Vinyl 3-Way 135º Splay Corner Cap allows you to join three separate lines of 135º Splay Bullnose Corners that meet at an Outside 90º corner. This vinyl corner cap can be fastened to the drywall with nails, screws, or adhesive. The Vinyl 3-Way 135º Splay Corner Cap (Off-Angle) is manufactured by Trim-Tex, Inc.